10/1/09

internet connectivity

Type of connection:

Broadband Internet access, often shortened to just broadband, is a high data rate Internet access—typically contrasted with dial-up access using a 56k modem.
Dial-up modems are limited to a bitrate of less than 56 kbit/s (kilobits per second) and require the full use of a telephone line—whereas broadband technologies supply more than double this rate and generally without disrupting telephone use.
Although various minimum bandwidths have been used in definitions of broadband, ranging up from 64 kbit/s up to 2.0 Mbit/s, the 2006 OECD report is typical by defining broadband as having download data transfer rates equal to or faster than 256 kbit/s, while the United States (US) Federal Communications Commission (FCC) as of 2009, defines "Basic Broadband" as data transmission speeds exceeding 768 kilobits per second (Kbps), or 768,000 bits per second, in at least one direction: downstream (from the Internet to the user’s computer) or upstream (from the user’s computer to the Internet). The trend is to raise the threshold of the broadband definition as the marketplace rolls out faster services.
Data rates are defined in terms of maximum download because several common consumer broadband technologies such as ADSL are "asymmetric"—supporting much slower maximum upload data rate than download.
Broadband is often called "high-speed" Internet, because it usually has a high rate of data transmission. In general, any connection to the customer of 256 kbit/s (0.256 Mbit/s) or greater is more concisely considered broadband Internet. The International Telecommunication Union Standardization Sector (ITU-T) recommendation I.113 has defined broadband as a transmission capacity that is faster than primary rate ISDN, at 1.5 to 2 Mbit/s. The FCC definition of broadband is 768 kbit/s (0.8 Mbit/s). The Organization for Economic Co-operation and Development (OECD) has defined broadband as 256 kbit/s in at least one direction and this bit rate is the most common baseline that is marketed as "broadband" around the world. There is no specific bitrate defined by the industry, however, and "broadband" can mean lower-bitrate transmission methods. Some Internet Service Providers (ISPs) use this to their advantage in marketing lower-bitrate connections as broadband.

In practice, the advertised bandwidth is not always reliably available to the customer; ISPs often allow a greater number of subscribers than their backbone connection or neighborhood access network can handle, under the assumption that most users will not be using their full connection capacity very frequently. This aggregation strategy works more often than not, so users can typically burst to their full bandwidth most of the time; however, peer-to-peer (P2P) file sharing systems, often requiring extended durations of high bandwidth, stress these assumptions, and can cause major problems for ISPs who have excessively overbooked their capacity. For more on this topic, see traffic shaping. As takeup for these introductory products increases, telcos are starting to offer higher bit rate services. For existing connections, this most of the time simply involves reconfiguring the existing equipment at each end of the connection.
As the bandwidth delivered to end users increases, the market expects that video on demand services streamed over the Internet will become more popular, though at the present time such services generally require specialized networks. The data rates on most broadband services still do not suffice to provide good quality video, as MPEG-2 video requires about 6 Mbit/s for good results. Adequate video for some purposes becomes possible at lower data rates, with rates of 768 kbit/s and 384 kbit/s used for some video conferencing applications, and rates as low as 100 kbit/s used for videophones using H.264/MPEG-4 AVC. The MPEG-4 format delivers high-quality video at 2 Mbit/s, at the low end of cable modem and ADSL performance.
In telecommunications and signal processing, baseband is an adjective that describes signals and systems whose range of frequencies is measured from zero to a maximum bandwidth or highest signal frequency; it is sometimes used as a noun for a band of frequencies starting at zero. It can often be considered as synonym to lowpass, and antonym to passband, bandpass or radio frequency (RF) signal.
A signal at baseband is often used to modulate a higher frequency carrier wave in order that it may be transmitted via radio. Modulation results in shifting the signal up to much higher frequencies (radio frequencies, or RF) than it originally spanned. A key consequence of the usual double-sideband amplitude modulation (AM) is that, usually, the range of frequencies the signal spans (its spectral bandwidth) is doubled. Thus, the RF bandwidth of a signal (measured from the lowest frequency as opposed to 0 Hz) is usually twice its baseband bandwidth. Steps may be taken to reduce this effect, such as single-sideband modulation; the highest frequency of such signals greatly exceeds the baseband bandwidth.
Some signals can be treated as baseband or not, depending on the situation. For example, a switched analog connection in the telephone network has energy below 300 Hz and above 3400 Hz removed by bandpass filtering; since the signal has no energy very close to zero frequency, it may not be considered a baseband signal, but in the telephone systems frequency-division multiplexing hierarchy, it is usually treated as a baseband signal, by comparison with the modulated signals used for long-distance transmission. The 300 Hz lower band edge in this case is treated as "near zero", being a small fraction of the upper band edge.

Baseband vs. Broadband

Data signals can be sent over a network cable in one of two ways: broadband or baseband. One good example of broadband signaling would be how you view different channels through your cable box and a signal coaxial cable carrying multiple signals in cable television.

Whereas, baseband signaling only sends a single signal over the cable. This type of signaling is typically used in Ethernet networks, with the exception of 10Broad3 standard (rarely used). Baseband uses very simple transceiver devices that send and receive signals on a cable. The simplicity behind baseband signaling is that only three states need to be distinquished: one, zero and idle. Broadband transceivers are much more complex because they must be able to distinquish those same states, but on multiple channels within the same cable. Because of its simplicity, baseband signaling is used on most Ethernet networks.

Type of topology:
Network topology is the physical interconnections of the elements (links, nodes, etc.) of a computer network. A local area network (LAN) is one example of a network that exhibits both a physical topology and a logical topology. Any given node in the LAN has one or more links to one or more other nodes in the network and the mapping of these links and nodes in a graph results in a geometrical shape that may be used to describe the physical topology of the network. Likewise, the mapping of the data flows between the nodes in the network determines the logical topology of the network. The physical and logical topologies may or may not be identical in any particular network.
Any particular network topology is determined only by the graphical mapping of the configuration of physical and/or logical connections between nodes. The study of network topology uses graph theory. Distances between nodes, physical interconnections, transmission rates, and/or signal types may differ in two networks and yet their topologies may be identical.

There are also three basic categories of network topologies:
• physical topologies
• signal topologies
• logical topologies

The terms signal topology and logical topology are often used interchangeably, though there is a subtle difference between the two.

Physical topologies
The mapping of the nodes of a network and the physical connections between them – i.e., the layout of wiring, cables, the locations of nodes, and the interconnections between the nodes and the cabling or wiring system.

Classification of physical topologies
Point-to-point

The simplest topology is a permanent link between two endpoints (the line in the illustration above). Switched point-to-point topologies are the basic model of conventional telephony. The value of a permanent point-to-point network is the value of guaranteed, or nearly so, communications between the two endpoints. The value of an on-demand point-to-point connection is proportional to the number of potential pairs of subscribers, and has been expressed as Metcalfe's Law.

Permanent (dedicated)

Easiest to understand, of the variations of point-to-point topology, is a point-to-point communications channel that appears, to the user, to be permanently associated with the two endpoints. Children's "tin-can telephone" is one example, with a microphone to a single public address speaker is another. These are examples of physical dedicated channels.
Within many switched telecommunications systems, it is possible to establish a permanent circuit. One example might be a telephone in the lobby of a public building, which is programmed to ring only the number of a telephone dispatcher. "Nailing down" a switched connection saves the cost of running a physical circuit between the two points. The resources in such a connection can be released when no longer needed, for example, a television circuit from a parade route back to the studio.

Switched:

Using circuit-switching or packet-switching technologies, a point-to-point circuit can be set up dynamically, and dropped when no longer needed. This is the basic mode of conventional telephony.


Bus network topology

In local area networks where bus technology is used, each machine is connected to a single cable. Each computer or server is connected to the single bus cable through some kind of connector. A terminator is required at each end of the bus cable to prevent the signal from bouncing back and forth on the bus cable. A signal from the source travels in both directions to all machines connected on the bus cable until it finds the MAC address or IP address on the network that is the intended recipient. If the machine address does not match the intended address for the data, the machine ignores the data. Alternatively, if the data does match the machine address, the data is accepted. Since the bus topology consists of only one wire, it is rather inexpensive to implement when compared to other topologies. However, the low cost of implementing the technology is offset by the high cost of managing the network. Additionally, since only one cable is utilized, it can be the single point of failure. If the network cable breaks, the entire network will be down, since there is only one cable. Since there is one cable, the transfer speeds between the computers on the network is faster.

Linear bus

The type of network topology in which all of the nodes of the network are connected to a common transmission medium which has exactly two endpoints (this is the 'bus', which is also commonly referred to as the backbone, or trunk) – all data that is transmitted between nodes in the network is transmitted over this common transmission medium and is able to be received by all nodes in the network virtually simultaneously (disregarding propagation delays).
Note: The two endpoints of the common transmission medium are normally terminated with a device called a terminator that exhibits the characteristic impedance of the transmission medium and which dissipates or absorbs the energy that remains in the signal to prevent the signal from being reflected or propagated back onto the transmission medium in the opposite direction, which would cause interference with and degradation of the signals on the transmission medium (See Electrical termination).
Distributed bus
The type of network topology in which all of the nodes of the network are connected to a common transmission medium which has more than two endpoints that are created by adding branches to the main section of the transmission medium – the physical distributed bus topology functions in exactly the same fashion as the physical linear bus topology (i.e., all nodes share a common transmission medium).

Notes:
1.) All of the endpoints of the common transmission medium are normally terminated with a device called a 'terminator' (see the note under linear bus).
2.) The physical linear bus topology is sometimes considered to be a special case of the physical distributed bus topology – i.e., a distributed bus with no branching segments.
3.) The physical distributed bus topology is sometimes incorrectly referred to as a physical tree topology – however, although the physical distributed bus topology resembles the physical tree topology, it differs from the physical tree topology in that there is no central node to which any other nodes are connected, since this hierarchical functionality is replaced by the common bus.


Star network topology

In local area networks where the star topology is used, each machine is connected to a central hub. In contrast to the bus topology, the star topology allows each machine on the network to have a point to point connection to the central hub. All of the traffic which transverses the network passes through the central hub. The hub acts as a signal booster or repeater which in turn allows the signal to travel greater distances. As a result of each machine connecting directly to the hub, the star topology is considered the easiest topology to design and implement. An advantage of the star topology is the simplicity of adding other machines. The primary disadvantage of the star topology is the hub is a single point of failure. If the hub were to fail the entire network would fail as a result of the hub being connected to every machine on the network.

Notes:
1.) A point-to-point link (described above) is sometimes categorized as a special instance of the physical star topology – therefore, the simplest type of network that is based upon the physical star topology would consist of one node with a single point-to-point link to a second node, the choice of which node is the 'hub' and which node is the 'spoke' being arbitrary.
2.) After the special case of the point-to-point link, as in note 1.) above, the next simplest type of network that is based upon the physical star topology would consist of one central node – the 'hub' – with two separate point-to-point links to two peripheral nodes – the 'spokes'.
3.) Although most networks that are based upon the physical star topology are commonly implemented using a special device such as a hub or switch as the central node (i.e., the 'hub' of the star), it is also possible to implement a network that is based upon the physical star topology using a computer or even a simple common connection point as the 'hub' or central node – however, since many illustrations of the physical star network topology depict the central node as one of these special devices, some confusion is possible, since this practice may lead to the misconception that a physical star network requires the central node to be one of these special devices, which is not true because a simple network consisting of three computers connected as in note 2.) above also has the topology of the physical star.
4.) Star networks may also be described as either broadcast multi-access or nonbroadcast multi-access (NBMA), depending on whether the technology of the network either automatically propagates a signal at the hub to all spokes, or only addresses individual spokes with each communication.

Extended star

A type of network topology in which a network that is based upon the physical star topology has one or more repeaters between the central node (the 'hub' of the star) and the peripheral or 'spoke' nodes, the repeaters being used to extend the maximum transmission distance of the point-to-point links between the central node and the peripheral nodes beyond that which is supported by the transmitter power of the central node or beyond that which is supported by the standard upon which the physical layer of the physical star network is based.

Note: If the repeaters in a network that is based upon the physical extended star topology are replaced with hubs or switches, then a hybrid network topology is created that is referred to as a physical hierarchical star topology, although some texts make no distinction between the two topologies.

Distributed Star

A type of network topology that is composed of individual networks that are based upon the physical star topology connected together in a linear fashion – i.e., 'daisy-chained' – with no central or top level connection point (e.g., two or more 'stacked' hubs, along with their associated star connected nodes or 'spokes').


Ring network topology

In local area networks where the ring topology is used, each computer is connected to the network in a closed loop or ring. Each machine or computer has a unique address that is used for identification purposes. The signal passes through each machine or computer connected to the ring in one direction. Ring topologies typically utilize a token passing scheme, used to control access to the network. By utilizing this scheme, only one machine can transmit on the network at a time. The machines or computers connected to the ring act as signal boosters or repeaters which strengthen the signals that transverse the network. The primary disadvantage of ring topology is the failure of one machine will cause the entire network to fail.

Mesh

The value of fully meshed networks is proportional to the exponent of the number of subscribers, assuming that communicating groups of any two endpoints, up to and including all the endpoints, is approximated by Reed's Law.

Fully connected mesh topology

The type of network topology in which each of the nodes of the network is connected to each of the other nodes in the network with a point-to-point link – this makes it possible for data to be simultaneously transmitted from any single node to all of the other nodes.
Note: The physical fully connected mesh topology is generally too costly and complex for practical networks, although the topology is used when there are only a small number of nodes to be interconnected.


Partially connected mesh topology

The type of network topology in which some of the nodes of the network are connected to more than one other node in the network with a point-to-point link – this makes it possible to take advantage of some of the redundancy that is provided by a physical fully connected mesh topology without the expense and complexity required for a connection between every node in the network.


Tree network topology

Also known as a hierarchical network. The type of network topology in which a central 'root' node (the top level of the hierarchy) is connected to one or more other nodes that are one level lower in the hierarchy (i.e., the second level) with a point-to-point link between each of the second level nodes and the top level central 'root' node, while each of the second level nodes that are connected to the top level central 'root' node will also have one or more other nodes that are one level lower in the hierarchy (i.e., the third level) connected to it, also with a point-to-point link, the top level central 'root' node being the only node that has no other node above it in the hierarchy (The hierarchy of the tree is symmetrical.) Each node in the network having a specific fixed number, of nodes connected to it at the next lower level in the hierarchy, the number, being referred to as the 'branching factor' of the hierarchical tree.


The list above shows what are the appropriate type of connection needed in our school and what kind of topology is best. As to what kind of mediums are better, i suggest we use low cost cables like coax or STP and UTP. Fiber optics are good but considering the financial status of our school, the three types above are more suited.




_________________
-=♥yhang♥=-

No comments:

listen...